Announcing PiAware 3!
Latest version is 3.5.3 (released November 6, 2017). Scroll down for the latest release notes.
FlightAware is excited to announce the launch of PiAware 3! PiAware 3 extends the industry leading capabilities of the incredibly popular PiAware software for Raspberry Pi devices. Highlights include mapping and aircraft list enhancements and easy WiFi setup. PiAware 3 is currently only available as a reinstall of the SD card image at this time. FlightAware recommends that all current users of PiAware upgrade to the PiAware 3 to obtain the new features.
Installing PiAware 3
The SD card image installation is the recommended procedure for users setting up a new Raspberry Pi for the first time or for users that want to update an existing PiAware device. Note that this will result in any existing data on the SD card being erased. To install, you must download the FlightAware PiAware 3 Raspberry Pi image which can be found here: https://flightaware.com/adsb/piaware/build
For discussion of the new features please use our discussion forum or e-mail adsbsupport [at] flightaware.com with questions.
- If you want to keep your existing SD card image and upgrade to version 3, see this post: ads-b-flight-tracking-f21/piaware-version-2-to-version-3-upgrade-t37890.html
- If you want to do a manual installation on your Raspberry Pi, see this post: ads-b-flight-tracking-f21/piaware-3-0-package-based-installation-t37851.html
Quickly, how do I enabled WiFi?
Note: These configuration instructions only apply if you installed from the PiAware 3.0 SD card image. If you need to enable WiFi then continue with the following steps AFTER completing the steps in Section 2 of the Build a PiAware instructions:
- Reinsert the SD card in your computer. It should be automatically recognized as an available disk drive.
- Open the SD card disk drive.
- Open “piaware-config.txt” in a text editor (usually you can just double-click the file to open).
- Scroll down to the “wifi” settings and change the following settings to the values specified here:
wireless-network yes wireless-ssid MyWifiNetwork (replace "MyWifiNetwork" with the name of your local WiFi network) wireless-password s3cr3t (replace "s3cr3t" with your local WiFi network password)
- Save and close the file.
- Eject and remove the SD card.
- Integrated WiFi support – Easy wifi configuration without requiring attached monitor/keyboard/mouse or wired network connectivity – please refer to the instructions on our web site: flightaware.com/adsb/piaware/bu … ional#wifi
- New OpenLayer Maps for local flight mapping.
Avoids requirement for users to obtain Google Maps API keys
Adds local map support for users in China
- Range rings and aircraft distance from receiver site
- Country flags
- Aircraft type and registration, when known
- Updates dump1090 to align with the latest dump1090-mutability release which includes a substantially better Mode S decoder than PiAware 2
- Adds support for receiver devices other than RTL-SDR dongles such as Beast, Radarcape and other external receivers (for advanced users)
- Adds a new configuration utility to ease setup and customization (for advanced users)
- Improves the update capabilities so you can easily receive future enhancements
- Adds a new PiAware status web page for easy status review at-a-glance and quick access to the local map view (for advanced users, this is on HTTP port 80 and port 8080 redirects here) – the easiest way to access this local map view continues to be via the “View Live Data” link on the My ADS-B stats page at https://flightaware.com
- Auto upgrade from 3.0.3 supported.
- Added support for additional wireless devices’ firmware.
- Added support for hidden wireless network SSIDs.
- piaware-config.txt now supports configuration values with special characters by enclosing them in quotes. This is primarily to support WiFi configuration. See comments in piaware-config.txt for details.
- Improvements to data decoding to prefer Extended Squitter data over non-ES Mode S data when both are available; this improves accuracy of reported data.
- Improved reliability of air/ground detection.
- Various minor bug fixes and tweaks.
- And the Big News: major improvements to the dump1090 web interface!
- Add NEXRAD weather layer (USA only)
- Aircraft information moves to drag-able pop-up
- Data table (sidebar) is resize-able and expandable/collapsible
- New and improved hyperlinks to flightaware.com aircraft data
- Configurable units of measure display (Imperial, metric, aeronautical)
- Filter aircraft by altitude
- Option to show all aircraft tracks
- Improved aircraft icons on map
- Improved aircraft type/registration database to include more publicly available data
- Computed aircraft registration numbers (from ICAO address) for countries with predictable mappings (e.g., USA)
- Various look and feel improvements for usability
- New config option: mlat-results-anon (default “yes”). Set to “no” to disable sending MLAT results for blocked aircraft.
- New command-line options: -configfile, -cachedir. Can be used to run multiple copies of piaware on a single host by pointing each piaware at a different config file and cachedir.
- Updated Mode A/C support:
New config option: allow-modeac (default “yes”). If enabled, dump1090-fa will decode Mode A/C if a client requests it via the Beast command protocol. Decoding Mode A/C requires additional CPU; this option may need to be disabled on low power devices. Upgrades on a Pi Zero or Pi 1 will set this to “no” during the upgrade. There is no display of Mode A/C data on the dump1090-fa web interface.
- Major improvements to the Mode A/C decoder. Greatly reduced dump1090 CPU load when processing Mode A/C data in a busy environment.
- Updated FlightAware’s aircraft static data export used by dump1090.
- Allow skipping the web map history load on slow connections by appending “#nohistory” to the map URL.
- For users running a previous 3.x SD card install or a new 3.3 SD card install:
Support for using external USB wifi on the Pi 3, for cases where the built-in wifi is insufficient. Configure “rfkill yes” in addition to normal wireless settings. This will disable the internal wifi and use the external USB wifi instead.
Added a splashscreen during boot.
PiAware will remind you to change your password when you log in if ssh is enabled and your password is still the default password.
- For users installing a NEW install from the 3.3 SD card image:
Updated the image to be based on the latest upstream Raspbian.
The sdcard image no longer includes a desktop environment; upstream changes in Raspbian made it impractical to maintain. If you need a desktop environment, you can either do a package install of piaware on top of standard Raspbian, or run the following after installing the image:
$ sudo apt-get update $ sudo apt-get install raspberrypi-ui-mods $ sudo reboot
- Replacing the desktop login prompt, after booting a simple text-mode status screen will be displayed. It shows (amongst other things) the current status of PiAware and the assigned IP addresses of the Pi. For a login prompt, press Alt+F2.
- The sdcard image no longer enables ssh by default for security reasons. This behaves the same way as upstream Raspbian; see raspberrypi.org/blog/a-secu … ian-pixel/ for more information. Upgrades of existing installs, without writing a new sdcard image, are not affected: if you had ssh enabled before, it’ll still be enabled after the upgrade. You can enable ssh by: Connecting a monitor and keyboard, logging in, running “sudo raspi-config”, and selecting “Interfacing options” then “Enable or disable ssh server”; or creating a file named “ssh” (it doesn’t matter what it contains) in the first partition of the sdcard. This can be done on a separate system, e.g. on a PC immediately after writing the sdcard image. ssh will be enabled on the next boot. See also raspberrypi.org/documentati … ccess/ssh/
- Various other bug fixes and tweaks.
- SD card image updated new kernel/bootloader packages (this adds support for the Pi Zero W)
- SD card image and package-based install updated to add PiAware Skyview user interface (dump1090 map view)
- Applied FlightAware branding and color scheme
- Improved row colors in data table for usability
- Add altitude color key to the map user interface
- Added color coded aircraft trails by aircraft altitude at each position
- Improved icons on the map view
- Added labels to distance range rings
- Updated aircraft icons to add more icons and make them consistent with flightaware.com
- Added new Settings pane (via gear icon) to consolidate configuration options and added filters for Blocked MLAT flights and ground vehicles.
- Added basic aircraft information pane the displays on hover over an aircraft icon.
- Updated and expanded the aircraft details pane for usability.
- Added current date/time in the header.
- Minor formatting changes for clarity and usability
- PiAware – make connections to FlightAware more robust for scalability/reliability
- Skyview – fix incorrect font in some browsers
- Skyview – fix incorrect “data source” displaying sometimes
- Skyview – show on-ground aircraft in brown color
- Skyview – speed up initial page load time
- Skyview – fix some incorrect aircraft icon mappings
- Skyview – fix unit selection on Firefox
- dump1090: Update OpenLayers to address SkyView performance issues on some browsers
- piaware: Fix a file descriptor leak when running on some non-Pi hardware
- piaware: Report current feeder ID from piaware-status
- fa-mlat-client: Fix complaints about out of order timestamps when mlat results are looped back
- fa-mlat-client: Fix a minor unit conversion error
- fa-mlat-client: Increase the size of socket listen queues to avoid false synflood detection
- piaware sdcard: Allow arbitrary strings (e.g. serial numbers) in rtlsdr-device-index
- piaware sdcard: Handle prehashed (64-character) wifi passphrases correctly
- piaware sdcard: Depend on a version of wpasupplicant that fixes the KRACK vulnerability